Workshop fabricated steel tanks. Part 1: Horizontal cylindrical single skin and double skin tanks for the underground storage of flammable and nonflammable water polluting liquids other than for heating and cooling of buildings
Tuote ladattavissa hetiToimitusaika on noin 1 - 2 työpäivääToimitusaika on 3 - 5 työpäivää.
This document specifies the product characteristics and test methods for workshop fabricated cylindrical, horizontal steel tanks, single (type S) and double skin (type D) intended to be used for the underground storage of water polluting liquids (both flammable and non-flammable) and installed in industrial processes or in petrol stations at normal ambient temperature conditions (-20 °C to +50 °C) within the following limits: - from 800 mm up to 3 000 mm nominal diameter and; - up to a maximum overall length of 6 times the nominal diameter; - with an operating pressure (Po) of maximum 50 kPa (0,5 bar(g)) and minimum – 5 kPa (–50 mbar(g)) and; - for double skin tanks with a vacuum leak detection system where the kinematic viscosity does not exceed 5 × 10-3 m2/s. Tanks designed to this standard allow for an earth cover of up to 1,5 m. If there are imposed traffic loads or a greater earth cover, calculation is expected to be carried out. This document is not applicable to tanks used for storage and/or supply of fuel/gas for building heating/cooling systems, and of hot or cold water not intended for human consumption, nor to loads and special measures necessary in areas subject to risk of earthquakes. Guidance on installation of tanks is presented in Annex A, which does not include special measures that might be necessary in areas subject to flooding. This document is not applicable for the storage of liquids having dangerous goods classes listed in Table 1 because of the special dangers involved. (...) NOTE The classifications referred to are those adopted by the United Nations Committee of Experts on the Transport of Dangerous Goods (not to be interpreted as tank classes described in 6.2).
Tämän julkaisun valmistelusta Suomessa vastaa Metalliteollisuuden Standardisointiyhdistys ry, puh. 09 19 231 (vaihde).
EN 10025-2:2004 Hot rolled products of structural steels - Part 2: Technical delivery conditions for non-alloy structural steels
EN 10204:2004 Metallic products - Types of inspection documents
EN 13160-1:2016 Leak detection systems - Part 1: General Principles
EN 10025-2:2004 Hot rolled products of structural steels - Part 2: Technical delivery conditions for non-alloy structural steels
EN 10204:2004 Metallic products - Types of inspection documents
EN 13160-1:2016 Leak detection systems - Part 1: General Principles
EN 13160-2:2016 Leak detection systems - Part 2: Requirements and test/assessment methods for pressure and vacuum systems
EN 13160-3:2016 Leak detection systems - Part 3: Requirements and test/assessment methods for liquid systems for tanks
EN 22768-1:1993 General tolerances - Part 1: Tolerances for linear and angular dimensions without individual tolerance indications (ISO 2768-1:1989)
EN 22768-2:1993 General tolerances - Part 2: Geometrical tolerances for features without individual tolerance indications (ISO 2768-2:1989)
EN ISO 12944-7:2017 Paints and varnishes - Corrosion protection of steel structures by protective paint systems - Part 7: Execution and supervision of paint work (ISO 12944-7:2017)
EN ISO 13920:1996 Welding - General tolerances for welded constructions - Dimensions for lengths and angles - Shape and position (ISO 13920:1996)
EN ISO 13920:2023 Welding - General tolerances for welded constructions - Dimensions for lengths and angles - Shape and position (ISO 13920:2023)
EN ISO 22081:2021 Geometrical product specifications (GPS) - Geometrical tolerancing - General geometrical specifications and general size specifications (ISO 22081:2021)
EN ISO 898-1:2013 Mechanical properties of fasteners made of carbon steel and alloy steel - Part 1: Bolts, screws and studs with specified property classes - Coarse thread and fine pitch thread (ISO 898-1:2013)