This document specifies requirements for the design, manufacture and marking of offshore containers with a maximum gross mass not exceeding 25 000 kg, intended for repeated use to, from and between offshore installations and ships. This document specifies only transport-related requirements.
Tämän julkaisun valmistelusta Suomessa vastaa SFS Suomen Standardit, puh. 09 149 9331.
Sisällysluettelo
Foreword
Introduction
1 Scope
2 Normative references
3 Terms and definitions
4 Symbols
5 Design
5.1 General
5.2 Structural strength
5.3 Welding
5.4 Additional design details
5.5 Tank containers
5.6 Containers for bulk solids
6 Materials
6.1 Steel — General
6.2 Rolled and extruded steels in offshore container structures
6.3 Aluminium
6.4 Non-metallic materials
6.5 Material documents
7 Type testing
7.1 General
7.2 Test equipment and calibration
7.3 Lifting test
7.4 Vertical impact test
7.5 Other tests
8 Production
8.1 General
8.2 Primary structure
8.3 Secondary structure
8.4 Production testing
8.5 Failure of production containers
9 Marking
9.1 Safety marking
9.2 Identification markings
9.3 Information markings
9.4 Other markings
10 Container data plate
10.1 General
10.2 Contents of data plate
11 Certificate of conformity
11.1 General
11.2 Documentation
11.3 Contents of the certificate of conformity
Annex A Regulations for offshore containers (informative)
ASME BPVC Section 9:2015
AWS D 1.1/D 1.1M:2015
EN 10025-1:2004 Hot rolled products of structural steels - Part 1: General technical delivery conditions
ASME BPVC Section 9:2015
AWS D 1.1/D 1.1M:2015
EN 10025-1:2004 Hot rolled products of structural steels - Part 1: General technical delivery conditions
EN 10025-2:2019 Hot rolled products of structural steels - Part 2: Technical delivery conditions for non-alloy structural steels
EN 10025-3:2019 Hot rolled products of structural steels - Part 3: Technical delivery conditions for normalized/normalized rolled weldable fine grain structural steels
EN 10025-4:2019 Hot rolled products of structural steels - Part 4: Technical delivery conditions for thermomechanical rolled weldable fine grain structural steels
EN 10025-4:2019+A1 Hot rolled products of structural steels - Part 4: Technical delivery conditions for thermomechanical rolled weldable fine grain structural steels
EN 10025-4:2019+A1:2022 Hot rolled products of structural steels - Part 4: Technical delivery conditions for thermomechanical rolled weldable fine grain structural steels
EN 10088-2:2014 Stainless steels - Part 2: Technical delivery conditions for sheet/plate and strip of corrosion resisting steels for general purposes
EN 10164:2018 Steel products with improved deformation properties perpendicular to the surface of the product - Technical delivery conditions
EN 10210-1:2006 Hot finished structural hollow sections of non-alloy and fine grain steels - Part 1: Technical delivery conditions
EN 10219-1:2006 Cold formed welded structural hollow sections of non-alloy and fine grain steels - Part 1: Technical delivery conditions
EN 10250-2:1999 Open die steel forgings for general engineering purposes - Part 2: Non-alloy quality and special steels
EN 10250-2:2022 Open die steel forgings for general engineering purposes - Part 2: Non-alloy quality and special steels
EN 10250-3:1999 Open die steel forgings for general engineering purposes - Part 3: Alloy special steels
EN 10250-3:2022 Open die steel forgings for general engineering purposes - Part 3: Alloy special steels
EN ISO 9606-1:2017 Qualification testing of welders - Fusion welding - Part 1: Steels (ISO 9606-1:2012 including Cor 1:2012 and Cor 2:2013)
ISO 10042:2005 Welding -- Arc-welded joints in aluminium and its alloys -- Quality levels for imperfections
ISO 10474:2013 Steel and steel products -- Inspection documents
ISO 10675-1:2016 Non-destructive testing of welds -- Acceptance levels for radiographic testing -- Part 1: Steel, nickel, titanium and their alloys
ISO 10675-2:2017 Non-destructive testing of welds -- Acceptance levels for radiographic testing -- Part 2: Aluminium and its alloys
ISO 1161:2016 Series 1 freight containers -- Corner and intermediate fittings -- Specifications
ISO 11666:2018 Non-destructive testing of welds -- Ultrasonic testing -- Acceptance levels
ISO 148-1:2016 Metallic materials -- Charpy pendulum impact test -- Part 1: Test method
ISO 1496-1:2013 Series 1 freight containers -- Specification and testing -- Part 1: General cargo containers for general purposes
ISO 1496-3:1995 Series 1 freight containers -- Specification and testing -- Part 3: Tank containers for liquids, gases and pressurized dry bulk
ISO 1496-4:1991 Series 1 freight containers -- Specification and testing -- Part 4: Non-pressurized containers for dry bulk
ISO 15607:2003 Specification and qualification of welding procedures for metallic materials -- General rules
ISO 15609-1:2004 Specification and qualification of welding procedures for metallic materials -- Welding procedure specification -- Part 1: Arc welding
ISO 15614-1:2017 Specification and qualification of welding procedures for metallic materials -- Welding procedure test -- Part 1: Arc and gas welding of steels and arc welding of nickel and nickel alloys
ISO 15614-2:2005 Specification and qualification of welding procedures for metallic materials -- Welding procedure test -- Part 2: Arc welding of aluminium and its alloys
ISO 17636-1:2013 Non-destructive testing of welds -- Radiographic testing -- Part 1: X- and gamma-ray techniques with film
ISO 17636-2:2013 Non-destructive testing of welds -- Radiographic testing -- Part 2: X- and gamma-ray techniques with digital detectors
ISO 17637:2016 Non-destructive testing of welds -- Visual testing of fusion-welded joints
ISO 17638:2016 Non-destructive testing of welds -- Magnetic particle testing
ISO 17640:2017 Non-destructive testing of welds -- Ultrasonic testing -- Techniques, testing levels, and assessment
ISO 209:2007 Aluminium and aluminium alloys -- Chemical composition
ISO 23277:2015 Non-destructive testing of welds -- Penetrant testing -- Acceptance levels
ISO 23278:2015 Non-destructive testing of welds -- Magnetic particle testing -- Acceptance levels
ISO 3452-1:2013 Non-destructive testing -- Penetrant testing -- Part 1: General principles
ISO 5817:2014 Welding -- Fusion-welded joints in steel, nickel, titanium and their alloys (beam welding excluded) -- Quality levels for imperfections
ISO 668:2013 Series 1 freight containers -- Classification, dimensions and ratings
ISO 6892-1:2016 Metallic materials -- Tensile testing -- Part 1: Method of test at room temperature
ISO 7500-1:2018 Metallic materials -- Calibration and verification of static uniaxial testing machines -- Part 1: Tension/compression testing machines -- Calibration and verification of the force-measuring system
ISO 9606-2:2004 Qualification test of welders -- Fusion welding -- Part 2: Aluminium and aluminium alloys
ISO 9712:2012 Non-destructive testing -- Qualification and certification of NDT personnel