Small craft. Hull construction and scantlings. Part 1: Materials: Thermosetting resins, glass-fibre reinforcement, reference laminate (ISO 12215-1:2000)
Tuote ladattavissa hetiToimitusaika on noin 1 - 2 työpäivääToimitusaika on 3 - 5 työpäivää.
This part of ISO 12215 is applicable to thermosetting resins and glass-fibre reinforcement used in the construction of small craft with a length of the hull (LH) of up to 24 m, in accordance with ISO 8666. This part of ISO 12215 specifies the minimum requirements for material properties of glass reinforcement and resin matrix and the reference laminate made thereof. This part of ISO 12215 may be applicable to materials other than those specified, provided that the minimum requirements and properties of the reference laminate are met.
Tämän julkaisun valmistelusta Suomessa vastaa Metalliteollisuuden Standardisointiyhdistys ry, puh. 09 19 231 (vaihde).
Sisällysluettelo
Foreword
1 Scope
2 Normative references
3 Terms and definitions
4 Requirements for material properties of small craft
ASTM D 4255/D 4255M:2015 Standard Test Method for In-Plane Shear Properties of Polymer Matrix Composite Materials by the Rail Shear Method
DIN 16945:1989
EN 59:1977 Glass reinforced plastics - Measurement of hardness by means of a Barcol impressor
ASTM D 4255/D 4255M:2015 Standard Test Method for In-Plane Shear Properties of Polymer Matrix Composite Materials by the Rail Shear Method
DIN 16945:1989
EN 59:1977 Glass reinforced plastics - Measurement of hardness by means of a Barcol impressor
ISO 14130:1997 Fibre-reinforced plastic composites -- Determination of apparent interlaminar shear strength by short-beam method
ISO 1675:1985 Plastics -- Liquid resins -- Determination of density by the pyknometer method
ISO 178:1993 Plastics -- Determination of flexural properties
ISO 1887:1995 Textile glass -- Determination of combustible-matter content
ISO 1889:1997 Reinforcement yarns -- Determination of linear density
ISO 2078:1993 Textile glass -- Yarns -- Designation
ISO 2535:1997 Plastics -- Unsaturated polyester resins -- Measurement of gel time at 25 degrees C
ISO 2555:1989 Plastics -- Resins in the liquid state or as emulsions or dispersions -- Determination of apparent viscosity by the Brookfield Test method
ISO 2811-1:1997 Paints and varnishes -- Determination of density -- Part 1: Pyknometer method
ISO 2884-1:1999 Paints and varnishes -- Determination of viscosity using rotary viscometers -- Part 1: Cone-and-plate viscometer operated at a high rate of shear
ISO 3344:1997 Reinforcement products -- Determination of moisture content
ISO 3374:2000 Reinforcement products -- Mats and fabrics -- Determination of mass per unit area
ISO 3521:1997 Plastics -- Unsaturated polyester and epoxy resins -- Determination of overall volume shrinkage
ISO 4901:1985 Reinforced plastics based on unsaturated polyester resins -- Determination of residual styrene monomer content
ISO 527-1:1993 Plastics -- Determination of tensile properties -- Part 1: General principles
ISO 527-4:1997 Plastics -- Determination of tensile properties -- Part 4: Test conditions for isotropic and orthotropic fibre-reinforced plastic composites
ISO 62:1999 Plastics -- Determination of water absorption
ISO 75-1:1993 Plastics -- Determination of temperature of deflection under load -- Part 1: General test method
ISO 75-2:1993 Plastics -- Determination of temperature of deflection under load -- Part 2: Plastics and ebonite
ISO 8666:2016 Small craft -- Principal data