Petroleum and natural gas industries. External coatings for buried or submerged pipelines used in pipeline transportation systems. Part 1: Polyolefin coatings (3-layer PE and 3-layer PP) (ISO 21809-1:2018)
Tuote ladattavissa hetiToimitusaika on noin 1 - 2 työpäivääToimitusaika on 3 - 5 työpäivää.
This document specifies requirements for plant-applied external three-layer polyethylene and polypropylene based coatings for corrosion protection of welded and seamless steel pipes for pipeline transportation systems in the petroleum and natural gas industries in accordance with ISO 13623. NOTE Pipes coated in accordance with this document are considered suitable for further protection by means of cathodic protection.
Tämän julkaisun valmistelusta Suomessa vastaa Metalliteollisuuden Standardisointiyhdistys ry, puh. 09 19 231 (vaihde).
Sisällysluettelo
Foreword
Introduction
1 Scope
2 Normative references
3 Terms and definitions
4 Conformance
4.1 Rounding
4.2 Compliance with this document
5 Symbols and abbreviated terms
5.1 Symbols
5.2 Abbreviations
6 Information supplied by the purchaser
6.1 General information
6.2 Additional information
7 Coating classification
7.1 General
7.2 Coating classes
7.3 Coating thickness classes
8 Qualification processes
8.1 General — Qualification scheme
8.2 Application procedure specification
8.3 Pre-production trial (PPT)
8.4 Inspection and testing plan (ITP)
8.5 Procedure qualification trial (PQT)
9 Coating material qualification
9.1 Composition of the coating system
9.2 Qualification of the coating materials
9.3 Batch certificate
9.4 Storage and handling of coating materials
10 Coating system qualification
11 Application of the coating system
11.1 General
11.2 Surface preparation
11.3 Coating application
11.4 Cutback
12 Inspection and testing
12.1 General
12.2 Re-testing
13 Coating repairs
14 Marking
14.1 General
14.2 Required markings
15 Handling and storage in the applicator’s facilities
15.1 Handling
15.2 Storage
16 Test reports and certificate of compliance
Annex A Inspection of thickness (normative)
Annex B Holiday detection test (normative)
Annex C Peel strength test (normative)
Annex D Thermal analysis of epoxy and cured epoxy coating film with Tg ≤ 115°C (normative)
Annex E Impact test (normative)
Annex F Indentation test (normative)
Annex G UV ageing test and thermal ageing test (normative)
Annex H Cathodic disbondment test (normative)
Annex I Flexibility test (normative)
Annex J Gel time of the epoxy powder (normative)
Annex K Total volatile/moisture content of the epoxy powder — Mass loss (normative)
ASTM D 1505:2018 Standard Test Method for Density of Plastics by the Density-Gradient Technique
ASTM D 1693:2015 Standard Test Method for Environmental Stress-Cracking of Ethylene Plastics
ASTM D 4940:2015 Standard Test Method for Conductimetric Analysis of Water Soluble Ionic Contamination of Blast Cleaning Abrasives
ASTM D 1505:2018 Standard Test Method for Density of Plastics by the Density-Gradient Technique
ASTM D 1693:2015 Standard Test Method for Environmental Stress-Cracking of Ethylene Plastics
ASTM D 4940:2015 Standard Test Method for Conductimetric Analysis of Water Soluble Ionic Contamination of Blast Cleaning Abrasives
ASTM D 792:2013 Standard Test Methods for Density and Specific Gravity (Relative Density) of Plastics by Displacement
EN 10204:2004 Metallic products - Types of inspection documents
ISO 10350-1:2017 Plastics -- Acquisition and presentation of comparable single-point data -- Part 1: Moulding materials
ISO 10474:2013 Steel and steel products -- Inspection documents
ISO 11124-1:2018 Preparation of steel substrates before application of paints and related products -- Specifications for metallic blast-cleaning abrasives -- Part 1: General introduction and classification
ISO 11124-2:2018 Preparation of steel substrates before application of paints and related products -- Specifications for metallic blast-cleaning abrasives -- Part 2: Chilled-iron grit
ISO 11124-3:2018 Preparation of steel substrates before application of paints and related products -- Specifications for metallic blast-cleaning abrasives -- Part 3: High-carbon cast-steel shot and grit
ISO 11124-4:2018 Preparation of steel substrates before application of paints and related products -- Specifications for metallic blast-cleaning abrasives -- Part 4: Low-carbon cast-steel shot
ISO 11126-10:2017 Preparation of steel substrates before application of paints and related products -- Specifications for non-metallic blast-cleaning abrasives -- Part 10: Almandite garnet
ISO 11126-1:2018 Preparation of steel substrates before application of paints and related products -- Specifications for non-metallic blast-cleaning abrasives -- Part 1: General introduction and classification
ISO 11126-3:2018 Preparation of steel substrates before application of paints and related products -- Specifications for non-metallic blast-cleaning abrasives -- Part 3: Copper refinery slag
ISO 11126-4:2018 Preparation of steel substrates before application of paints and related products -- Specifications for non-metallic blast-cleaning abrasives -- Part 4: Coal furnace slag
ISO 11126-5:2018 Preparation of steel substrates before application of paints and related products -- Specifications for non-metallic blast-cleaning abrasives -- Part 5: Nickel slag
ISO 11126-6:2018 Preparation of steel substrates before application of paints and related products -- Specifications for non-metallic blast-cleaning abrasives -- Part 6: Iron and steel slags
ISO 11126-7:2018 Preparation of steel substrates before application of paints and related products -- Specifications for non-metallic blast-cleaning abrasives -- Part 7: Fused aluminium oxide
ISO 11126-8:2018 Preparation of steel substrates before application of paints and related products -- Specifications for non-metallic blast-cleaning abrasives -- Part 8: Olivine
ISO 11126-9:1999 Preparation of steel substrates before application of paints and related products -- Specifications for non-metallic blast-cleaning abrasives -- Part 9: Staurolite
ISO 1133-1:2011 Plastics -- Determination of the melt mass-flow rate (MFR) and melt volume-flow rate (MVR) of thermoplastics -- Part 1: Standard method
ISO 11357-2:2013 Plastics -- Differential scanning calorimetry (DSC) -- Part 2: Determination of glass transition temperature and glass transition step height
ISO 11357-6:2018 Plastics -- Differential scanning calorimetry (DSC) -- Part 6: Determination of oxidation induction time (isothermal OIT) and oxidation induction temperature (dynamic OIT)
ISO 1183-1:2012 Plastics -- Methods for determining the density of non-cellular plastics -- Part 1: Immersion method, liquid pyknometer method and titration method
ISO 1183-2:2004 Plastics -- Methods for determining the density of non-cellular plastics -- Part 2: Density gradient column method
ISO 1183-3:1999 Plastics -- Methods for determining the density of non-cellular plastics -- Part 3: Gas pyknometer method
ISO 15512:2016 Plastics -- Determination of water content
ISO 17855-2:2016 Plastics -- Polyethylene (PE) moulding and extrusion materials -- Part 2: Preparation of test specimens and determination of properties
ISO 179-1:2010 Plastics -- Determination of Charpy impact properties -- Part 1: Non-instrumented impact test
ISO 179-2:1997 Plastics -- Determination of Charpy impact properties -- Part 2: Instrumented impact test
ISO 18553:2002 Method for the assessment of the degree of pigment or carbon black dispersion in polyolefin pipes, fittings and compounds
ISO 19069-2:2016 Plastics -- Polypropylene (PP) moulding and extrusion materials -- Part 2: Preparation of test specimens and determination of properties
ISO 21809-2:2014 Petroleum and natural gas industries -- External coatings for buried or submerged pipelines used in pipeline transportation systems -- Part 2: Single layer fusion-bonded epoxy coatings
ISO 2808:2007 Paints and varnishes -- Determination of film thickness
ISO 2811-1:2016 Paints and varnishes -- Determination of density -- Part 1: Pycnometer method
ISO 2811-2:2011 Paints and varnishes -- Determination of density -- Part 2: Immersed body (plummet) method
ISO 2811-3:2011 Paints and varnishes -- Determination of density -- Part 3: Oscillation method
ISO 2811-4:2011 Paints and varnishes -- Determination of density -- Part 4: Pressure cup method
ISO 306:2013 Plastics -- Thermoplastic materials -- Determination of Vicat softening temperature (VST)
ISO 3183:2012 Petroleum and natural gas industries -- Steel pipe for pipeline transportation systems
ISO 3251:2008 Paints, varnishes and plastics -- Determination of non-volatile-matter content
ISO 4892-2:2013 Plastics -- Methods of exposure to laboratory light sources -- Part 2: Xenon-arc lamps
ISO 527-1:2012 Plastics -- Determination of tensile properties -- Part 1: General principles
ISO 527-2:2012 Plastics -- Determination of tensile properties -- Part 2: Test conditions for moulding and extrusion plastics
ISO 6964:1986 Polyolefin pipes and fittings -- Determination of carbon black content by calcination and pyrolysis -- Test method and basic specification
ISO 80000-1:2009 Quantities and units -- Part 1: General
ISO 8130-2:1992 Coating powders -- Part 2: Determination of density by gas comparison pyknometer (referee method)
ISO 8130-3:1992 Coating powders -- Part 3: Determination of density by liquid displacement pyknometer
ISO 8130-7:1992 Coating powders -- Part 7: Determination of loss of mass on stoving
ISO 8501-1:2007 Preparation of steel substrates before application of paints and related products -- Visual assessment of surface cleanliness -- Part 1: Rust grades and preparation grades of uncoated steel substrates and of steel substrates after overall removal of previous coatings
ISO 8502-3:2017 Preparation of steel substrates before application of paints and related products -- Tests for the assessment of surface cleanliness -- Part 3: Assessment of dust on steel surfaces prepared for painting (pressure-sensitive tape method)
ISO 8502-6:2006 Preparation of steel substrates before application of paints and related products -- Tests for the assessment of surface cleanliness -- Part 6: Extraction of soluble contaminants for analysis -- The Bresle method
ISO 8502-9:1998 Preparation of steel substrates before application of paints and related products -- Tests for the assessment of surface cleanliness -- Part 9: Field method for the conductometric determination of water-soluble salts
ISO 8503-4:2012 Preparation of steel substrates before application of paints and related products -- Surface roughness characteristics of blast-cleaned steel substrates -- Part 4: Method for the calibration of ISO surface profile comparators and for the determination of surface profile -- Stylus instrument procedure
ISO 8503-5:2017 Preparation of steel substrates before application of paints and related products -- Surface roughness characteristics of blast-cleaned steel substrates -- Part 5: Replica tape method for the determination of the surface profile
ISO 868:2003 Plastics and ebonite -- Determination of indentation hardness by means of a durometer (Shore hardness)
SSPC-AB 1:1991
SSPC-AB 2:1996
SSPC-AB 3:2003
SSPC-Guide 15:2013
SSPC-SP 1:1982