ISO 11148-13:2017 specifies safety requirements for hand-held non-electric power tools (hereinafter referred to as "fastener driving tools") intended for installation of a fastener (see Annex B), forming a mechanical connection or attachment with the workpiece which are for example wood and wood-based materials, plastic materials, fibre materials (loose or compacted), cementitious materials, metals and combinations of these materials. The fastener driving tools for fasteners can be powered by compressed air or combustible gases (which may be ignited by a battery or accumulator) and the energy is transmitted to an impacted element by an intermediary component that does not leave the device. These tools are intended to be used by one operator and supported by the operator's hand or hands, with or without a suspension, e.g. a balancer. ISO 11148-13:2017 is applicable to fastener driving tools in which energy is applied to a loaded fastener for the purpose of driving this into a workpiece. ISO 11148-13:2017 is not applicable to fastener driving tools in which the energy for driving fasteners is drawn from powder-actuated cartridges, hydraulics or from any type of electrical supply. ISO 11148-13:2017 does not deal with special requirements and modifications of hand-held power tools for the purpose of mounting them in a fixture. ISO 11148-13:2017 deals with all significant hazards, hazardous situations or hazardous events relevant to fastener driving tools for fasteners when they are used as intended and under conditions of misuse which are reasonably foreseeable by the manufacturer, with the exception of the use of power tools in potentially explosive atmospheres. NOTE ISO 80079?36 gives requirements for non-electrical equipment for potentially explosive atmospheres.
Tämän julkaisun valmistelusta Suomessa vastaa Metalliteollisuuden Standardisointiyhdistys ry, puh. 09 19 231 (vaihde).
Sisällysluettelo
Foreword
Introduction
1 Scope
2 Normative references
3 Terms and definitions
3.1 General terms
3.2 Terms and definitions related to fastener driving tools
4 Safety requirements and measures
4.1 General
4.2 Mechanical safety
4.3 Electrical safety
4.4 Thermal safety
4.5 Noise reduction
4.6 Mechanical impact (vibration/recoil)
4.7 Materials and substances processed, used or emitted
4.8 Ergonomics
4.9 User information
4.10 Fire and explosion
5 Verification
5.1 General
5.2 Protection against mechanical hazards
5.3 Electrical safety
5.4 Thermal safety
5.5 Noise
5.6 Mechanical impact (vibration/recoil)
5.7 Materials and substances processed, used or emitted
5.8 Ergonomics
5.9 User information
5.10 Fire and explosion
5.11 Structure of verification
6 Information for use
6.1 Markings
6.2 Instruction handbook
6.3 Operating instructions
6.4 Data
6.5 Maintenance instructions
Annex A List of significant hazards (informative)
Annex B Example of fastener driving tools covered by ISO 11148–13 (informative)
Annex C Symbols for labels and signs (normative)
Annex D Warnings and symbols for labels and signs for tools with contact actuation capability (normative)
Annex E Information on the ergonomic design of the handle (informative)
EN 12096:1997 Mechanical vibration - Declaration and verification of vibration emission values
EN 12549:1999+A1:2008 Acoustics - Noise test code for fastener driving tools - Engineering method
EN 15895:2011 Cartridge operated hand-held tools - Safety requirements - Fixing and hard marking tools
EN 12096:1997 Mechanical vibration - Declaration and verification of vibration emission values
EN 12549:1999+A1:2008 Acoustics - Noise test code for fastener driving tools - Engineering method
EN 15895:2011 Cartridge operated hand-held tools - Safety requirements - Fixing and hard marking tools
ISO 12100:2010 Safety of machinery -- General principles for design -- Risk assessment and risk reduction
ISO 13732-1:2006 Ergonomics of the thermal environment -- Methods for the assessment of human responses to contact with surfaces -- Part 1: Hot surfaces
ISO 13732-3:2005 Ergonomics of the thermal environment -- Methods for the assessment of human responses to contact with surfaces -- Part 3: Cold surfaces
ISO 3864-2:2016 Graphical symbols -- Safety colours and safety signs -- Part 2: Design principles for product safety labels
ISO 4871:1996 Acoustics -- Declaration and verification of noise emission values of machinery and equipment
ISO 7010:2011 Graphical symbols -- Safety colours and safety signs -- Registered safety signs
ISO 8662-11:1999 Hand-held portable power tools -- Measurement of vibrations at the handle -- Part 11: Fastener driving tools
ISO 8662-11:1999/Amd 1:2001