IEC 60966-1:2019 is available as IEC 60966-1:2019 RLV which contains the International Standard and its Redline version, showing all changes of the technical content compared to the previous edition.IEC 60966-1:2019 specifies requirements for radio frequency coaxial cable assemblies operating in the transverse electromagnetic mode (TEM) and establishes general requirements for testing the electrical, mechanical and environmental properties of radio frequency coaxial cable assemblies composed of cables and connectors. Additional requirements relating to specific families of cable assemblies are given in the relevant sectional specifications. This third edition cancels and replaces the second edition published in 1999. This edition includes the following significant technical changes with respect to the previous edition:
a) measurement method for screening effectiveness was cancelled;
b) give references to relevant test procedures for transfer impedance and screening attenuation
Tämän julkaisun valmistelusta Suomessa vastaa SESKO ry, puh. 050 571 6048.
EN 60068-1:2014 Ympäristöolosuhdetestaus. Osa 1: Yleistä ja opastusta
EN 60068-2-11:1999 Environmental testing - Part 2: Tests - Test Ka: Salt mist
EN 60068-2-14:2009 Environmental testing - Part 2-14: Tests - Test N: Change of temperature
EN 60068-1:2014 Ympäristöolosuhdetestaus. Osa 1: Yleistä ja opastusta
EN 60068-2-11:1999 Environmental testing - Part 2: Tests - Test Ka: Salt mist
EN 60068-2-14:2009 Environmental testing - Part 2-14: Tests - Test N: Change of temperature
EN 60068-2-27:2009 Environmental testing - Part 2-27: Tests - Test Ea and guidance: Shock
EN 60068-2-42:2003 Environmental testing - Part 2-42: Tests - Test Kc: Sulphur dioxide test for contacts and connections
EN 60068-2-68:1996 Environmental testing - Part 2: Tests - Test L: Dust and sand
EN 60068-2-6:2008 Environmental testing - Part 2-6: Tests - Test Fc: Vibration (sinusoidal)
EN 60068-2-78:2013 Environmental testing - Part 2-78: Tests - Test Cab: Damp heat, steady state
EN 60068-4:1996 Environmental testing - Part 4: Information for specification writers - Test summaries
EN 60332-1-2:2004 Tests on electric and optical fibre cables under fire conditions - Part 1-2: Test for vertical flame propagation for a single insulated wire or cable - Procedure for 1 kW pre-mixed flame
EN 60512-6-2:2002 Connectors for electronic equipment - Tests and measurements - Part 6-2: Dynamic stress tests - Test 6b: Bump
EN 60512-7-2:2012 Connectors for electronic equipment - Tests and measurements - Part 7-2: Impact tests (free connectors) - Test 7b: Mechanical strength impact
EN 60529:1991 Sähkölaitteiden kotelointiluokat (IP-koodi)
EN 60966-2-1:2009 Radio frequency and coaxial cable assemblies - Part 2-1: Sectional specification for flexible coaxial cable assemblies
EN 60966-2-2:1994 Radio frequency and coaxial cable assemblies - Part 2-2: Blank detail specification for flexible coaxial cable assemblies
EN 60966-2-2:2003 Radio frequency and coaxial cable assemblies - Part 2-2: Blank detail specification for flexible coaxial cable assemblies
EN 60966-2-3:1999 Radio frequency and coaxial cable assemblies - Part 2-3: Detail specification for flexible coaxial cable assemblies
EN 60966-2-3:2003 Radio frequency and coaxial cable assemblies - Part 2-3: Detail specification for flexible coaxial cable assemblies
EN 60966-2-3:2009 Radio frequency and coaxial cable assemblies - Part 2-3: Detail specification for flexible coaxial cable assemblies - Frequency range 0 MHz to 1 000 MHz, IEC 61169-8 connectors
EN 60966-2-4:1997 Radio frequency and coaxial cable assemblies - Part 2-4: Detail specification for cable assemblies for radio and TV receivers (Frequency range 0 to 3 000 MHz, IEC 60169-2 connectors)
EN 60966-2-4:2003 Radio frequency and coaxial cables assemblies - Part 2-4: Detail specification for cable assemblies for radio and TV receivers - Frequency range 0 to 3 000 MHz, IEC 61169-2 connectors
EN 60966-2-4:2009 Radio frequency and coaxial cable assemblies - Part 2-4: Detail specification for cable assemblies for radio and TV receivers - Frequency range 0 MHz to 3 000 MHz, IEC 61169-2 connectors
EN 60966-2-4:2016 Radio Frequency and coaxial cable assemblies - Part 2-4: Detail specification for cable assemblies for radio and TV receivers - Frequency range 0 MHz to 3 000 MHz, IEC 61169-2 connectors
EN 60966-2-5:1999 Radio frequency and coaxial cable assemblies - Part 2-5: Detail specification for cable assemblies for radio and TV receivers - Frequency range 0 to 1 000 MHz, IEC 60169-2 connectors
EN 60966-2-5:2003 Radio frequency and coaxial cable assemblies - Part 2-5: Detail specification for cable assemblies for radio and TV receivers - Frequency range 0 to 1 000 MHz, IEC 61169-2 connectors
EN 60966-2-5:2009 Radio frequency and coaxial cable assemblies - Part 2-5: Detail specification for cable assemblies for radio and TV receivers - Frequency range 0 MHz to 1 000 MHz, IEC 61169-2 connectors
EN 60966-2-5:2017 Radio frequency and coaxial cable assemblies - Part 2-5: Detail specification for cable assemblies for radio and TV receivers - Frequency range 0 MHz to 1 000 MHz, IEC 61169-2 connectors
EN 60966-2-6:1999 Radio frequency and coaxial cable assemblies - Part 2-6: Detail specification for cable assemblies for radio and TV receivers - Frequency range 0 to 3 000 MHz, IEC 60169-24 connectors
EN 60966-2-6:2003 Radio frequency and coaxial cable assemblies - Part 2-6: Detail specification for cable assemblies for radio and TV receivers - Frequency range 0 to 3 000 MHz, IEC 61169-24 connectors
EN 60966-2-6:2009 Radio frequency and coaxial cable assemblies - Part 2-6: Detail specification for cable assemblies for radio and TV receivers - Frequency range 0 MHz to 3 000 MHz, IEC 61169-24 connectors
EN 60966-2-6:2017 Radio frequency and coaxial cable assemblies - Part 2-6: Detail specification for cable assemblies for radio and TV receivers - Frequency range 0 MHz to 3 000 MHz, IEC 61169-24 connectors
EN 60966-2-7:2016 Radio frequency and coaxial cable assemblies - Part 2-7: Detail specification for cable assemblies for radio and TV receivers - Frequency range 0 MHz to 3 000 MHz, IEC 61169-47 connectors
EN 60966-3-1:2009 Radio frequency and coaxial cable assemblies - Part 3-1: Blank detail specification for semi-flexible coaxial cable assemblies
EN 60966-3-2:1999 Radio frequency and coaxial cable assemblies - Part 3-2: Detail specification for semi-flexible coaxial cable assemblies for GSM use (0,8 GHz - 1 GHz)
EN 60966-3-2:2003 Radio frequency and coaxial cable assemblies - Part 3-2: Detail specification for semi-flexible coaxial cable assemblies for GSM use (0,8 GHz - 1 GHz)
EN 60966-4-1:2003 Radio frequency and coaxial cable assemblies - Part 4-1: Blank detail specification for semi-rigid coaxial cable assemblies
EN 61169-11:2017 Radio-frequency connectors - Part 11: Sectional specification for RF coaxial connectors with inner diameter of outer conductor 9,5 mm with threaded coupling - Characteristic impedance 50 O (type 4,1-9,5)
EN 61169-14:2010 Radio-frequency connectors - Part 14: R.F. coaxial connectors with inner diameter of outer conductor 12 mm with screw coupling - Characteristic impedance 75 ohms (Type 3,5/12)
EN 61169-16:2007 Radio-frequency connectors - Part 16: Sectional specification - RF coaxial connectors with inner diameter of outer conductor 7 mm (0,276 in) with screw coupling - Characteristic impedance 50 ohms (75 ohms) (type N)
EN 61169-18:2011 Radio-frequency connectors - Part 18: Sectional specification - Radio frequency coaxial connectors of type SSMA
EN 61169-19:2011 Radio-frequency connectors - Part 19: Sectional specification - Radio frequency coaxial connectors of type SSMB
EN 61169-1:2013 Radio-frequency connectors - Part 1: Generic specification - General requirements and measuring methods
EN 61169-24:2001 Radio-frequency connectors - Part 24: Sectional specification - Radio frequency coaxial connectors with screw coupling, typically for use in 75 ohm cable distribution systems (type F)
EN 61169-24:2009 Radio-frequency connectors - Part 24: Sectional specification - Radio frequency coaxial connectors with screw coupling, typically for use in 75 ohm cable networks (type F)
EN 61169-26:2013 Radio-frequency connectors - Part 26: Sectional specification for TNCA series RF coaxial connectors
EN 61169-29:2005 Radio-frequency connectors - Part 29: Sectional specification - Miniature radio frequency coaxial connectors model screw, snap-on, push-pull or quick-lock, slide-in (rack and panel applications) - Characteristic impedance 50 ohms (type 1,0/2,3) - 50 omhs and 75 ohms applications
EN 61169-2:2001 Radio-frequency connectors - Part 2: Sectional specification - Radio frequency coaxial connectors of type 9,52
EN 61169-2:2007 Radio-frequency connectors - Part 2: Sectional specification - Radio frequency coaxial connectors of type 9,52
EN 61169-31:1999 Radio-frequency connectors - Part 31: RF coaxial connectors with inner diameter of outer conductor 1,0 mm (0,039 in) with screw coupling - Characteristic impedance 50 ohms (type 1,0)
EN 61169-32:1999 Radio-frequency connectors - Part 32: RF coaxial connectors with inner diameter of outer conductor 1,85 mm (0,072 in) with screw coupling - Characteristic impedance 50 ohms (type 1,85)
EN 61169-33:1997 Radio-frequency connectors - Part 33: Sectional specification for series BMA r.f. connectors
EN 61169-35:2011 Radio-frequency connectors - Part 35: Sectional specification for 2,92 series RF connectors
EN 61169-36:1997 Radio-frequency connectors - Part 36: Sectional specification for microminiature r.f. coaxial connectors with snap-on coupling - Characteristic impedance 50 ohm (type MCX)
EN 61169-37:2007 Radio-frequency connectors - Part 37: Sectional specification for STWX8 R.F connectors
EN 61169-38:2009 Radio-frequency connectors - Part 38: Sectional specification - Radio frequency coaxial connectors model, slide-in (rack and panel applications) - Characteristic impedance 50 O (type TMA) - 50 O applications
EN 61169-39:2011 Radio-frequency connectors - Part 39: Sectional specification for CQM series quick lock RF connectors
EN 61169-40:2011 Radio-frequency connectors - Part 40: Sectional specification for 2.4 series RF connectors
EN 61169-41:2011 Radio-frequency connectors - Part 41: Sectional specification for CQA series quick lock R.F. coaxial connectors
EN 61169-42:2013 Radio-frequency connectors - Part 42: Sectional specification for CQN series quick lock RF coaxial connectors
EN 61169-43:2013 Radio-frequency connectors - Part 43: Sectional specification for RBMA series blind mating RF coaxial connectors
EN 61169-44:2013 Radio-frequency connectors - Part 44: Sectional specification for series SMP push-on radio-frequency coaxial connectors
EN 61169-45:2014 Radio-frequency connectors -Part 45: Sectional specification for series SQMA series quick lock RF coaxial connectors
EN 61169-47:2012 Radio-frequency connectors - Part 47: Sectional specification for radio-frequency coaxial connectors with clamp coupling, typically for use in 75 O cable networks (type F-Quick)
EN 61169-47:2015 Radio-frequency connectors - Part 47: Sectional specification for radio-frequency coaxial connectors with clamp coupling, typically for use in 75 O cable networks (type F-Quick)
EN 61169-48:2015 Radio-frequency connectors - Part 48: Sectional specification for series BMP R.F. coaxial connectors
EN 61169-49:2014 Radio-frequency connectors - Part 49: Sectional specification for SMAA series R.F connectors
EN 61169-50:2015 Radio-frequency connectors - Part 50: Sectional specification for RF coaxial connectors with inner diameter of outer conductors 4,11 mm with quick lock system - Characteristic impedance 50 Ohm (type QMA)
EN 61169-51:2015 Radio-frequency connectors - Part 51: Sectional specification for RF coaxial connectors with inner diameter of outer conductors 13,5 mm with bayonet lock - Characteristic impedance 50 Ohm (type QLI)
EN 61169-52:2015 Radio-frequency connectors - Part 52: Sectional specification for series MMCX RF coaxial connectors
EN 61169-53:2016 Radio-frequency connectors - Part 53: Sectional specification for RF coaxial connectors with inner diameter of outer conductor 16 mm with screw lock - Characteristic impedance 50 Ohm (Type S7-16)
EN 61169-54:2016 Radio-frequency connectors - Part 54: Sectional specification for coaxial connectors with 10 mm inner diameter of outer conductor, nominal characteristic impedance 50 O, series 4,3-10
EN 61169-58:2016 Radio-frequency connectors - Part 58: Sectional specification for RF coaxial connectors with blind-mate coupling - Characteristic impedance 50 O (type SBMA)
EN 61169-59:2017 Radio-frequency connectors - Part 59: Sectional specification for type L32-4 and L32-5 threaded multi-pin radio-frequency connectors
EN 61169-8:2007 Radio-frequency connectors - Part 8: Sectional specification - RF coaxial connectors with inner diameter of outer conductor 6,5 mm (0,256 in) with bayonet lock - Characteristic impedance 50 ohms (type BNC)
EN 62037-2:2013 Passive RF and microwave devices, intermodulation level measurement - Part 2: Measurement of passive intermodulation in coaxial cable assemblies
EN 62153-4-7:2016 Metallic communication cable test methods - Part 4-7: Electromagnetic compatibility (EMC) - Test method for measuring of transfer impedance ZT and screening attenuation as or coupling attenuation ac of connectors and assemblies up to and above 3 GHz - Triaxial tube in tube method
EN IEC 60068-2-11:2021 Environmental testing - Part 2-11: Tests - Test Ka: Salt mist
EN IEC 60068-2-14:2023 Environmental testing - Part 2-14: Tests - Test N: Change of temperature
EN IEC 60966-2-1:2024 Radio frequency and coaxial cable assemblies - Part 2-1: Sectional specification for flexible coaxial cable assemblies
EN IEC 60966-2-2:2024 Radio frequency and coaxial cable assemblies - Part 2-2: Blank detail specification for flexible coaxial cable assemblies
EN IEC 60966-2-8:2022 Radio frequency and coaxial cable assemblies - Part 2-8: Detail specification for cable assemblies for radio and TV receivers - Frequency range up to 3 000 MHz, Screening class A++, IEC 61169-47 connectors
EN IEC 60966-3-1:2023 Radio frequency and coaxial cable assemblies - Part 3-1: Blank detail specification for semi-flexible coaxial cable assemblies
EN IEC 60966-3-3:2023 Radio frequency and coaxial cable assemblies - Part 3-3: Detail specification for semi-flexible cable assemblies (Jumper) - Frequency range up to 18 GHz, Type 50-141 semi-flexible coaxial cable
EN IEC 60966-3-4:2023 Radio frequency and coaxial cable assemblies - Part 3-4: Detail specification for semi-flexible cable assemblies (Jumper) - Frequency range up to 6 GHz, Type 50-141 semi-flexible coaxial cable
EN IEC 60966-4-1:2024 Radio frequency and coaxial cable assemblies - Part 4-1: Blank detail specification for semi-rigid coaxial cable assemblies
EN IEC 60966-4-2:2022 Radio frequency and coaxial cable assemblies - Part 4-2: Detail specification for semi rigid cable assemblies (jumper) - Frequency range up to 6000 MHz, type 50-9 semi-rigid coaxial cable
EN IEC 60966-4-3:2022 Radio frequency and coaxial cable assemblies - Part 4-3: Detail specification for semi-rigid cable assemblies - Frequency range up to 6 000 MHz, type 50-12 low loss semi-rigid coaxial cable
EN IEC 62037-2:2021 Passive RF and microwave devices, intermodulation level measurement - Part 2: Measurement of passive intermodulation in coaxial cable assemblies
IEC 61196-1-119:2012
IEC 62153-4-6:2017