Plastics. Unplasticized poly(vinyl chloride) (PVC-U) moulding and extrusion materials. Part 2: Preparation of test specimens and determination of properties (ISO 21306-2:2019)
Tuote ladattavissa hetiToimitusaika on noin 1 - 2 työpäivääToimitusaika on 3 - 5 työpäivää.
This document specifies the methods of preparation of test specimens and the test methods to be used in determining the properties of PVC-U moulding and extrusion materials. Requirements for handling test materials and for conditioning both the test material before moulding and the specimens before testing are given. The properties required for the designation of PVC-U thermoplastics are given in ISO 21306-1. All properties are intended to be determined by the appropriate methods referred to in this document and values obtained shall be presented as laid down in ISO 10350-1. The values determined in accordance with this document are not necessarily be identical to those obtained using specimens of different dimensions and/or prepared by different procedures. The values obtained for the properties of a moulding depend on the moulding compound, the shape, the test method and the state of anisotropy. The last-mentioned depends on the gating of the mould and the moulding conditions, for example temperature, pressure and injection rate. Any subsequent treatment is also be considered, for example conditioning or annealing. The thermal history and the internal stresses of the specimens can strongly influence the thermal and mechanical properties and the resistance to environmental stress cracking, but exert less effect on the electrical properties, which depend mainly on the chemical composition of the moulding compound. In order to obtain reproducible and comparable test results, the methods of preparation and conditioning, the specimen dimensions and the test procedures specified herein are used. Values determined are not necessarily be identical to those obtained using specimens of different dimensions or prepared using different procedures.
Tämän julkaisun valmistelusta Suomessa vastaa Kemesta ry, puh. 040 820 4888.
IEC 60112:2003
IEC 60243-1:2013
IEC 60250:1969
IEC 60296:2012
IEC 60695-11-10:2013
IEC 62631-3-1:2016
IEC 62631-3-2:2015
ISO 10350-1:2017 Plastics -- Acquisition and presentation of comparable single-point data -- Part 1: Moulding materials
ISO 1183-1:2012 Plastics -- Methods for determining the density of non-cellular plastics -- Part 1: Immersion method, liquid pyknometer method and titration method
ISO 1183-2:2019 Plastics -- Methods for determining the density of non-cellular plastics -- Part 2: Density gradient column method
ISO 1183-3:1999 Plastics -- Methods for determining the density of non-cellular plastics -- Part 3: Gas pyknometer method
ISO 178:2019 Plastics -- Determination of flexural properties
ISO 179-1:2010 Plastics -- Determination of Charpy impact properties -- Part 1: Non-instrumented impact test
ISO 179-2:1997 Plastics -- Determination of Charpy impact properties -- Part 2: Instrumented impact test
ISO 20753:2018 Plastics -- Test specimens
ISO 21306-1:2019 Plastics -- Unplasticized poly(vinyl chloride) (PVC-U) moulding and extrusion materials -- Part 1: Designation system and basis for specifications
ISO 2818:2018 Plastics -- Preparation of test specimens by machining
ISO 291:2008 Plastics -- Standard atmospheres for conditioning and testing
ISO 293:2004 Plastics -- Compression moulding of test specimens of thermoplastic materials
ISO 306:2013 Plastics -- Thermoplastic materials -- Determination of Vicat softening temperature (VST)
ISO 4589-2:2017 Plastics -- Determination of burning behaviour by oxygen index -- Part 2: Ambient-temperature test
ISO 4589-3:2017 Plastics -- Determination of burning behaviour by oxygen index -- Part 3: Elevated-temperature test
ISO 527-1:2012 Plastics -- Determination of tensile properties -- Part 1: General principles
ISO 527-2:2012 Plastics -- Determination of tensile properties -- Part 2: Test conditions for moulding and extrusion plastics
ISO 527-4:1997 Plastics -- Determination of tensile properties -- Part 4: Test conditions for isotropic and orthotropic fibre-reinforced plastic composites
ISO 62:2008 Plastics -- Determination of water absorption
ISO 75-1:2013 Plastics -- Determination of temperature of deflection under load -- Part 1: General test method
ISO 75-2:2013 Plastics -- Determination of temperature of deflection under load -- Part 2: Plastics and ebonite
ISO 8256:2004 Plastics -- Determination of tensile-impact strength
ISO 899-1:2017 Plastics -- Determination of creep behaviour -- Part 1: Tensile creep