SFS-EN 1433 + AC:en

Soveltamisala

Suomenkielistä soveltamisalaa ei ole saatavissa.

This European Standard specifies requirements for prefabricated linear drainage channels for the collection and conveyance of surface water when installed within areas subject to pedestrian and/or vehicular traffic. It applies to grid units, slot units and kerb units up to a clear opening of 1000 mm.

Tämän julkaisun valmistelusta Suomessa vastaa Metalliteollisuuden Standardisointiyhdistys ry, puh. 09 19 231 (vaihde).

Tuoteryhmä(t)

93.030 Viemäriverkostot »
93.080.30 Tietekniikan laitteet ja asennukset »
90.064 Jäteveden käsittelytuotteet lukuunottamatta putkia »

Sidokset

Velvoittavat viittaukset

EN 10080:2005 Steel for the reinforcement of concrete - Weldable reinforcing steel - General
EN 10088-1:2014 Stainless steels - Part 1: List of stainless steels
EN 10088-1:2023 Stainless steels - Part 1: List of stainless steels

EN 10080:2005 Steel for the reinforcement of concrete - Weldable reinforcing steel - General
EN 10088-1:2014 Stainless steels - Part 1: List of stainless steels
EN 10088-1:2023 Stainless steels - Part 1: List of stainless steels
EN 10088-2:2014 Stainless steels - Part 2: Technical delivery conditions for sheet/plate and strip of corrosion resisting steels for general purposes
EN 10088-3:2014 Stainless steels - Part 3: Technical delivery conditions for semi-finished products, bars, rods, wire, sections and bright products of corrosion resisting steels for general purposes
EN 10088-3:2023 Stainless steels - Part 3: Technical delivery conditions for semi-finished products, bars, rods, wire, sections and bright products of corrosion resistant steels for general purposes
EN 10346:2015 Continuously hot-dip coated steel flat products for cold forming - Technical delivery conditions
EN 1169:1999 Precast concrete products - General rules for factory production control of glass-fibre reinforced cement
EN 1170-5:1997 Precast concrete products - Test method for glass-fibre reinforced cement - Part 5: Measuring bending strength, "Complete bending test" method
EN 12163:2016 Copper and copper alloys - Rod for general purposes
EN 1563:2018 Founding - Spheroidal graphite cast irons
EN ISO 7500-1:2018 Metallic materials - Calibration and verification of static uniaxial testing machines - Part 1: Tension/compression testing machines - Calibration and verification of the force-measuring system (ISO 7500-1:2018)
ISO 1461:1999 Hot dip galvanized coatings on fabricated iron and steel articles -- Specifications and test methods
ISO 185:1988 Grey cast iron -- Classification
ISO 3755:1991 Cast carbon steels for general engineering purposes
ISO 4012:1978 Concrete -- Determination of compressive strength of test specimens
ISO 630:1995 Structural steels -- Plates, wide flats, bars, sections and profiles
ISO 8062:1994 Castings -- System of dimensional tolerances and machining allowances

Tekninen komitea

CEN/TC 165 Waste water engineering »

Direktiivi

89/106/EEC Rakennustuotedirektiivi
93/38/EEC Vesi- ja energiahuollon, liikenteen ja teletoiminnan alan hankintoja koskevien sopimusten tekomenettelyjen yhteensovittamisesta
305/2011 Rakennustuotteet

http://ec.europa.eu »

Vahvistuspäivä

02.06.2003

Julkaisupäivä

19.06.2003

Painos

1

Sivumäärä

61

Julkaisun kieli

englanti

Lisätiedot

Varmista hEN Helpdeskistä, onko standardin tämä versio CE-merkintään voimassa oleva versio.