This document specifies a series of methods for the determination of the ability of a pressure sensitive tape to remain adhered under a constant load applied parallel to the surfaces of the tape and substrate. This document contains: — method A: Self adhesive tapes ? Measurement of shear adhesion to a vertical standard steel panel; — method B: Self adhesive tapes ? Measurement of shear adhesion to a vertical panel covered with NIST SRM 1810A[1] standard fibreboard; — method C: Self adhesive tapes ? Measurement of shear adhesion to a vertical panel covered with a fibreboard agreed upon by the buyer and seller; — method D: Self adhesive tapes ? Measurement of shear adhesion of filament reinforced tape applied to a horizontal standard steel panel; — method E: Self adhesive tapes ? Measurement of shear adhesion of filament reinforced tape applied to a horizontal panel covered with NIST SRM 1810A1) standard fibreboard; — method F: Self adhesive tapes ? Measurement of shear adhesion of filament reinforced tape applied to a horizontal panel covered with a fibreboard agreed upon by the buyer and seller; — method G: Self adhesive tapes ? Measurement of shear adhesion to a vertical standard steel panel at elevated temperature after a 10 min dwell time.
[1] NIST SRM 1810A is National Institute of Standards and Technology ? Standard Reference Material 1810A and is available from the Institute at Gaithersburg, Maryland MD 20899, USA.
Tämän julkaisun valmistelusta Suomessa vastaa Kemesta ry, puh. 040 820 4888.
Sisällysluettelo
Foreword
Introduction
1 Scope
2 Normative references
3 Terms and definitions
4 Significance and use
5 Method A: Measurement of shear adhesion to a vertical standard steel panel
5.1 Principle
5.2 Materials
5.3 Apparatus
5.4 Test samples and test piece
5.5 Procedure
5.6 Expression of results
5.7 Test report
6 Method B: Measurement of shear adhesion to a vertical panel covered with NIST SRM 1810A standard fibreboard
6.1 Principle
6.2 Materials
6.3 Apparatus
6.4 Test samples and test piece
6.5 Procedure
6.6 Expression of results
6.7 Test report
7 Method C: Measurement of shear adhesion to a vertical panel covered with a fibreboard agreed upon by the buyer and the seller
7.1 Principle
7.2 Procedure
8 Method D: Measurement of shear adhesion of filament reinforced tape applied to a horizontal standard steel panel
8.1 Principle
8.2 Materials
8.3 Apparatus
8.4 Test samples and test piece
8.5 Procedure
8.6 Expression of results
8.7 Test report
9 Method E: Measurement of shear adhesion of filament reinforced tape applied to a horizontal panel covered with NIST SRM 1810A standard fibreboard
9.1 Principle
9.2 Procedure
10 Method F: Measurement of shear adhesion of filament reinforced tape applied to a horizontal panel covered with a fibreboard agreed upon by the buyer and the seller
10.1 Principle
10.2 Procedure
11 Method G: Measurement of shear adhesion to a vertical standard steel panel at an elevated temperature after 10 min dwell time
5 Method A: Measurement of shear adhesion to a vertical standard steel panel
5.1 Principle
5.2 Materials
5.3 Apparatus
5.4 Test samples and test piece
5.5 Procedure
5.6 Expression of results
5.7 Test report
6 Method B: Measurement of shear adhesion to a vertical panel covered with NIST SRM 1810A standard fibreboard
6.1 Principle
6.2 Materials
6.3 Apparatus
6.4 Test samples and test piece
6.5 Procedure
6.6 Expression of results
6.7 Test report
7 Method C: Measurement of shear adhesion to a vertical panel covered with a fibreboard agreed upon by the buyer and the seller
7.1 Principle
7.2 Procedure
8 Method D: Measurement of shear adhesion of filament reinforced tape applied to a horizontal standard steel panel
8.1 Principle
8.2 Materials
8.3 Apparatus
8.4 Test samples and test piece
8.5 Procedure
8.6 Expression of results
8.7 Test report
9 Method E: Measurement of shear adhesion of filament reinforced tape applied to a horizontal panel covered with NIST SRM 1810A standard fibreboard
9.1 Principle
9.2 Procedure
10 Method F: Measurement of shear adhesion of filament reinforced tape applied to a horizontal panel covered with a fibreboard agreed upon by the buyer and the seller
10.1 Principle
10.2 Procedure
11 Method G: Measurement of shear adhesion to a vertical standard steel panel at an elevated temperature after 10 min dwell time