SFS-EN ISO 23153-2:2020:en

Soveltamisala

Suomenkielistä soveltamisalaa ei ole saatavissa.

This document specifies the methods of preparation of test specimens and the test methods to be used in determining the properties of polyetheretherketone (PEEK) moulding and extrusion materials. Requirements for handling test material and for conditioning both the test material before moulding and the specimens before testing are given.
Procedures and conditions for the preparation of test specimens and procedures for measuring properties of the materials from which these specimens are made are also given. Properties and test methods that are suitable and necessary to characterize PEEK moulding and extrusion materials are listed.
In order to obtain reproducible and comparable test results, the methods of preparation and conditioning, the specimen dimensions and the test procedures specified herein are used. Values determined will not necessarily be identical to those obtained using specimens of different dimensions or prepared using different procedures.

Tämän julkaisun valmistelusta Suomessa vastaa Kemesta ry, puh. 040 820 4888.

Sisällysluettelo

Tuoteryhmä(t)

83.080.20 Kestomuovit »

Sidokset

Velvoittavat viittaukset

IEC 60112:2003 Method for the determination of the proof and the comparative tracking indices of solid insulating materials
IEC 60243-1:2013 Electric strength of insulating materials - Test methods - Part 1: Tests at power frequencies
IEC 60296:2012 Fluids for electrotechnical applications - Unused mineral insulating oils for transformers and switchgear

IEC 60112:2003 Method for the determination of the proof and the comparative tracking indices of solid insulating materials
IEC 60243-1:2013 Electric strength of insulating materials - Test methods - Part 1: Tests at power frequencies
IEC 60296:2012 Fluids for electrotechnical applications - Unused mineral insulating oils for transformers and switchgear
IEC 60695-11-10:2013 Fire hazard testing - Part 11-10: Test flames - 50 W horizontal and vertical flame test methods
IEC 62631-2-1:2018 Dielectric and resistive properties of solid insulating materials - Part 2-1: Relative permittivity and dissipation factor - Technical Frequencies (0,1 Hz - 10 MHz) - AC Methods
IEC 62631-3-1:2016 Dielectric and resistive properties of solid insulating materials - Part 3-1: Determination of resistive properties (DC methods) - Volume resistance and volume resistivity - General method
ISO 10350-1:2017 Plastics -- Acquisition and presentation of comparable single-point data -- Part 1: Moulding materials
ISO 1133-1:2011 Plastics -- Determination of the melt mass-flow rate (MFR) and melt volume-flow rate (MVR) of thermoplastics -- Part 1: Standard method
ISO 11357-2:2013 Plastics -- Differential scanning calorimetry (DSC) -- Part 2: Determination of glass transition temperature and glass transition step height
ISO 11357-3:2018 Plastics -- Differential scanning calorimetry (DSC) -- Part 3: Determination of temperature and enthalpy of melting and crystallization
ISO 11359-2:1999 Plastics -- Thermomechanical analysis (TMA) -- Part 2: Determination of coefficient of linear thermal expansion and glass transition temperature
ISO 11443:2014 Plastics -- Determination of the fluidity of plastics using capillary and slit-die rheometers
ISO 1183-1:2019 Plastics -- Methods for determining the density of non-cellular plastics -- Part 1: Immersion method, liquid pycnometer method and titration method
ISO 1183-3:1999 Plastics -- Methods for determining the density of non-cellular plastics -- Part 3: Gas pyknometer method
ISO 15512:2019 Plastics -- Determination of water content
ISO 178:2019 Plastics -- Determination of flexural properties
ISO 179-1:2010 Plastics -- Determination of Charpy impact properties -- Part 1: Non-instrumented impact test
ISO 20753:2018 Plastics -- Test specimens
ISO 23153-1:2020 Plastics -- Polyetheretherketone (PEEK) moulding and extrusion materials -- Part 1: Designation system and basis for specifications
ISO 294-1:2017 Plastics -- Injection moulding of test specimens of thermoplastic materials -- Part 1: General principles, and moulding of multipurpose and bar test specimens
ISO 294-3:2002 Plastics -- Injection moulding of test specimens of thermoplastic materials -- Part 3: Small plates
ISO 294-4:2018 Plastics -- Injection moulding of test specimens of thermoplastic materials -- Part 4: Determination of moulding shrinkage
ISO 3915:1981 Plastics -- Measurement of resistivity of conductive plastics
ISO 527-1:2019 Plastics -- Determination of tensile properties -- Part 1: General principles
ISO 527-2:2012 Plastics -- Determination of tensile properties -- Part 2: Test conditions for moulding and extrusion plastics
ISO 62:2008 Plastics -- Determination of water absorption
ISO 75-1:2013 Plastics -- Determination of temperature of deflection under load -- Part 1: General test method
ISO 75-2:2013 Plastics -- Determination of temperature of deflection under load -- Part 2: Plastics and ebonite

Tekninen komitea

CEN/TC 249 Plastics »

Vahvistuspäivä

07.02.2020

Julkaisupäivä

11.02.2020

Painos

1

Sivumäärä

11

Julkaisun kieli

englanti