SFS-ISO/IEC 26550:2020:en

Soveltamisala

Suomenkielistä soveltamisalaa ei ole saatavissa.

This International Standard is the entry point of the whole suite of International Standards for software and systems product line engineering and management. The scope of this International Standard is to This International Standard does not describe any methods and tools associated with software and systems product line engineering and management. Descriptions of such methods and tools will appear in the consecutive International Standards (ISO/IEC 265511
1 Second edition to be published. to ISO/IEC 265562
2 Under development.). This International Standard does not deal with terms and definitions addressed by ISO/IEC/IEEE 24765:2010 that provides a common vocabulary applicable to all systems and software engineering work. Whenever this International Standard refers to “products”, it means “system-level products” consisting of software systems or both hardware and software systems. It may be useful for the engineering and management of product lines that consist of only hardware systems but it has not been explicitly created to support such hardware product lines. This International Standard is not intended to help the engineering, production, warehousing, logistics, and management of physical items that, possibly combined with software, comprise the products. These processes belong to other disciplines (e.g. mechanics, electronics). This International Standard, including the product line reference model and the terms and definitions, has been produced starting from References [6], [7], and [8] which finally resulted in a broad consensus from National Member Bodies at the time of publication. In addition to this background process, structures from ISO/IEC 12207:2008, ISO/IEC/IEEE 15288:2015, ISO/IEC 15940:2006 and ISO/IEC 14102:2008 have been used as a baseline.

Tämän julkaisun valmistelusta Suomessa vastaa SFS Suomen Standardit, puh. 09 149 9331.

Sisällysluettelo

Foreword
Introduction
1 Scope
2 Normative references
3 Terms and definitions
4 From single-system engineering and management toward product line engineering and management

4.1 Challenges product companies face in the use of single-system engineering and management
4.2 Variability management
4.3 Key differentiators between single-system engineering and management and product line engineering and management

5 Reference model for product line engineering and management

5.1 General
5.2 Product line reference model

6 Two life cycles and two process groups for product line engineering and management

6.1 Domain engineering life cycle
6.2 Application engineering life cycle
6.3 Organizational management process group
6.4 Technical management process group

7 Relationships within and between domain engineering and application engineering

7.1 Interrelations between product line scoping and domain requirements engineering
7.2 Interrelations between domain requirements engineering and domain design
7.3 Interrelations between domain design and domain realization
7.4 Interrelations between domain requirements engineering and domain verification and validation
7.5 Interrelations between domain design and domain verification and validation
7.6 Interrelations between domain realization and domain verification and validation
7.7 Interrelations between product line scoping and application requirements engineering
7.8 Interrelations between domain requirements engineering and application requirements engineering
7.9 Interrelations between domain design and application design
7.10 Interrelations between domain realization and application realization
7.11 Interrelations between domain verification and validation and application verification and validation
7.12 Interrelations between application requirements engineering and application design
7.13 Interrelations between application design and application realization
7.14 Interrelations between application requirements engineering and application verification and validation
7.15 Interrelations between application design and application verification and validation
7.16 Interrelations between application realization and application verification and validation

Annex A Further information on products (informative)

Bibliography

Näytä kaikki

Foreword
Introduction
1 Scope
2 Normative references
3 Terms and definitions
4 From single-system engineering and management toward product line engineering and management

4.1 Challenges product companies face in the use of single-system engineering and management
4.2 Variability management
4.3 Key differentiators between single-system engineering and management and product line engineering and management

5 Reference model for product line engineering and management

5.1 General
5.2 Product line reference model

6 Two life cycles and two process groups for product line engineering and management

6.1 Domain engineering life cycle
6.2 Application engineering life cycle
6.3 Organizational management process group
6.4 Technical management process group

7 Relationships within and between domain engineering and application engineering

7.1 Interrelations between product line scoping and domain requirements engineering
7.2 Interrelations between domain requirements engineering and domain design
7.3 Interrelations between domain design and domain realization
7.4 Interrelations between domain requirements engineering and domain verification and validation
7.5 Interrelations between domain design and domain verification and validation
7.6 Interrelations between domain realization and domain verification and validation
7.7 Interrelations between product line scoping and application requirements engineering
7.8 Interrelations between domain requirements engineering and application requirements engineering
7.9 Interrelations between domain design and application design
7.10 Interrelations between domain realization and application realization
7.11 Interrelations between domain verification and validation and application verification and validation
7.12 Interrelations between application requirements engineering and application design
7.13 Interrelations between application design and application realization
7.14 Interrelations between application requirements engineering and application verification and validation
7.15 Interrelations between application design and application verification and validation
7.16 Interrelations between application realization and application verification and validation

Annex A Further information on products (informative)

Bibliography

Tuoteryhmä(t)

35.080 Ohjelmistot »
96.100.20 Työkalut ja ympäristöt »

Sidokset

Velvoittavat viittaukset

Tässä julkaisussa ei ole velvoittavia viittauksia

Tekninen komitea

ISO/IEC JTC 1/SC 7 (SFS-julkaisut) Software and systems engineering »

Vahvistuspäivä

14.08.2020

Julkaisupäivä

18.08.2020

Painos

1

Sivumäärä

39

Julkaisun kieli

englanti