ISO 10350 identifies specific test procedures for the acquisition and presentation of comparable data for certain basic properties of plastics. In general, each property is specified by a single experimental value, although in certain cases properties are represented by two values obtained under different test conditions or along different directions in the material. The properties included are those presented conventionally in manufacturers' data sheets. This document applies to reinforced thermoplastic and thermosetting materials where the reinforcement fibres are either discontinuous with a fibre length prior to processing greater than 7,5 mm or continuous (e.g. fabric, continuous-strand mat or unidirectional). ISO 10350-1 deals specifically with unreinforced and filled plastics, including those using fibres less than 7,5 mm in length.
Tämän julkaisun valmistelusta Suomessa vastaa Kemesta ry, puh. 040 820 4888.
IEC 60112:2003 Method for the determination of the proof and the comparative tracking indices of solid insulating materials
IEC 60243-1:2013 Electric strength of insulating materials - Test methods - Part 1: Tests at power frequencies
IEC 60296:2020 Fluids for electrotechnical applications – Mineral insulating oils for electrical equipment
IEC 60112:2003 Method for the determination of the proof and the comparative tracking indices of solid insulating materials
IEC 60243-1:2013 Electric strength of insulating materials - Test methods - Part 1: Tests at power frequencies
IEC 60296:2020 Fluids for electrotechnical applications – Mineral insulating oils for electrical equipment
IEC 60695-11-10:2013 Fire hazard testing - Part 11-10: Test flames - 50 W horizontal and vertical flame test methods
IEC 60695-11-20:2015 Fire hazard testing - Part 11-20: Test flames - 500 W flame test method
IEC 62631-2-1:2018 Dielectric and resistive properties of solid insulating materials - Part 2-1: Relative permittivity and dissipation factor - Technical Frequencies (0,1 Hz - 10 MHz) - AC Methods
IEC 62631-3-1:2016 Dielectric and resistive properties of solid insulating materials - Part 3-1: Determination of resistive properties (DC methods) - Volume resistance and volume resistivity - General method
IEC 62631-3-2:2015 Dielectric and resistive properties of solid insulating materials - Part 3-2: Determination of resistive properties (DC methods) - Surface resistance and surface resistivity
ISO 11357-2:2020 Plastics -- Differential scanning calorimetry (DSC) -- Part 2: Determination of glass transition temperature and step height
ISO 11357-3:2018 Plastics -- Differential scanning calorimetry (DSC) -- Part 3: Determination of temperature and enthalpy of melting and crystallization
ISO 11359-2:1999 Plastics -- Thermomechanical analysis (TMA) -- Part 2: Determination of coefficient of linear thermal expansion and glass transition temperature
ISO 1172:1996 Textile-glass-reinforced plastics -- Prepregs, moulding compounds and laminates -- Determination of the textile-glass and mineral-filler content -- Calcination methods
ISO 1183-1:2019 Plastics -- Methods for determining the density of non-cellular plastics -- Part 1: Immersion method, liquid pycnometer method and titration method
ISO 1183-2:2019 Plastics -- Methods for determining the density of non-cellular plastics -- Part 2: Density gradient column method
ISO 1183-3:1999 Plastics -- Methods for determining the density of non-cellular plastics -- Part 3: Gas pyknometer method
ISO 1268-10:2005 Fibre-reinforced plastics -- Methods of producing test plates -- Part 10: Injection moulding of BMC and other long-fibre moulding compounds -- General principles and moulding of multipurpose test specimens
ISO 1268-11:2005 Fibre-reinforced plastics -- Methods of producing test plates -- Part 11: Injection moulding of BMC and other long-fibre moulding compounds -- Small plates
ISO 1268-1:2001 Fibre-reinforced plastics -- Methods of producing test plates -- Part 1: General conditions
ISO 1268-2:2001 Fibre-reinforced plastics -- Methods of producing test plates -- Part 2: Contact and spray-up moulding
ISO 1268-3:2000 Fibre-reinforced plastics -- Methods of producing test plates -- Part 3: Wet compression moulding
ISO 1268-4:2005 Fibre-reinforced plastics -- Methods of producing test plates -- Part 4: Moulding of prepregs
ISO 1268-4:2005/Amd 1:2010
ISO 1268-5:2001 Fibre-reinforced plastics -- Methods of producing test plates -- Part 5: Filament winding
ISO 1268-6:2002 Fibre-reinforced plastics -- Methods of producing test plates -- Part 6: Pultrusion moulding
ISO 1268-7:2001 Fibre-reinforced plastics -- Methods of producing test plates -- Part 7: Resin transfer moulding
ISO 1268-8:2004 Fibre-reinforced plastics -- Methods of producing test plates -- Part 8: Compression moulding of SMC and BMC
ISO 1268-9:2003 Fibre-reinforced plastics -- Methods of producing test plates -- Part 9: Moulding of GMT/STC
ISO 14125:1998 Fibre-reinforced plastic composites -- Determination of flexural properties
ISO 14127:2008 Carbon-fibre-reinforced composites -- Determination of the resin, fibre and void contents
ISO 14130:1997 Fibre-reinforced plastic composites -- Determination of apparent interlaminar shear strength by short-beam method
ISO 15310:1999 Fibre-reinforced plastic composites -- Determination of the in-plane shear modulus by the plate twist method
ISO 179-1:2010 Plastics -- Determination of Charpy impact properties -- Part 1: Non-instrumented impact test
ISO 179-2:2020 Plastics -- Determination of Charpy impact properties -- Part 2: Instrumented impact test
ISO 2577:2007 Plastics -- Thermosetting moulding materials -- Determination of shrinkage
ISO 2818:2018 Plastics -- Preparation of test specimens by machining
ISO 291:2008 Plastics -- Standard atmospheres for conditioning and testing
ISO 3915:1981 Plastics -- Measurement of resistivity of conductive plastics
ISO 4589-2:2017 Plastics -- Determination of burning behaviour by oxygen index -- Part 2: Ambient-temperature test
ISO 527-4:1997 Plastics -- Determination of tensile properties -- Part 4: Test conditions for isotropic and orthotropic fibre-reinforced plastic composites
ISO 527-5:2009 Plastics -- Determination of tensile properties -- Part 5: Test conditions for unidirectional fibre-reinforced plastic composites
ISO 62:2008 Plastics -- Determination of water absorption
ISO 6603-2:2000 Plastics -- Determination of puncture impact behaviour of rigid plastics -- Part 2: Instrumented impact testing
ISO 75-3:2004 Plastics -- Determination of temperature of deflection under load -- Part 3: High-strength thermosetting laminates and long-fibre-reinforced plastics
ISO 7822:1990 Textile glass reinforced plastics -- Determination of void content -- Loss on ignition, mechanical disintegration and statistical counting methods