Verkkokauppa
SFS-EN 1993-1-5:en
Eurocode 3. Design of steel structures. Part 1-5: Plated structural elements
Soveltamisala
Suomenkielistä soveltamisalaa ei ole saatavissa.
(1) EN 1993-1-5 gives design requirements of stiffened and unstiffened plates which are subject to inplane
forces.
(2) Effects due to shear lag, in-plane load introduction and plate buckling for I-section girders and box
girders are covered. Also covered are plated structural components subject to in-plane loads as in tanks and
silos. The effects of out-of-plane loading are outside the scope of this document.
NOTE 1: The rules in this part complement the rules for class 1, 2, 3 and 4 sections, see EN 1993-1-1.
NOTE 2: For the design of slender plates which are subject to repeated direct stress and/or shear and also
fatigue due to out-of-plane bending of plate elements (breathing) see EN 1993-2 and EN 1993-6.
NOTE 3: For the effects of out-of-plane loading and for the combination of in-plane effects and out-of-plane
loading effects see EN 1993-2 and EN 1993-1-7.
NOTE 4: Single plate elements may be considered as flat where the curvature radius r satisfies:
t
a
r
2
³ (1.1)
where a is the panel width
t is the plate thickness
Tämän julkaisun valmistelusta Suomessa vastaa Metalliteollisuuden Standardisointiyhdistys ry, puh. 09 19 231 (vaihde).
(1) EN 1993-1-5 gives design requirements of stiffened and unstiffened plates which are subject to inplane
forces.
(2) Effects due to shear lag, in-plane load introduction and plate buckling for I-section girders and box
girders are covered. Also covered are plated structural components subject to in-plane loads as in tanks and
silos. The effects of out-of-plane loading are outside the scope of this document.
NOTE 1: The rules in this part complement the rules for class 1, 2, 3 and 4 sections, see EN 1993-1-1.
NOTE 2: For the design of slender plates which are subject to repeated direct stress and/or shear and also
fatigue due to out-of-plane bending of plate elements (breathing) see EN 1993-2 and EN 1993-6.
NOTE 3: For the effects of out-of-plane loading and for the combination of in-plane effects and out-of-plane
loading effects see EN 1993-2 and EN 1993-1-7.
NOTE 4: Single plate elements may be considered as flat where the curvature radius r satisfies:
t
a
r
2
³ (1.1)
where a is the panel width
t is the plate thickness
Tämän julkaisun valmistelusta Suomessa vastaa Metalliteollisuuden Standardisointiyhdistys ry, puh. 09 19 231 (vaihde).
Tuoteryhmä(t)
Sidokset
Velvoittavat viittaukset
EN 1993-1-1:2005 Eurocode 3: Design of steel structures - Part 1-1: General rules and rules for buildings
EN 1993-1-1:2022 Eurocode 3 - Design of steel structures - Part 1-1: General rules and rules for buildings
EN 1993-1-1:2022 Eurocode 3 - Design of steel structures - Part 1-1: General rules and rules for buildings
Tekninen komitea
Direktiivi
Vahvistuspäivä
18.12.2006
Julkaisupäivä
12.01.2007
Painos
1
Sivumäärä
54
Julkaisun kieli
englanti
Lisätiedot
Tämä on nk. ensimmäisen sukupolven eurokoodi, joka on edelleen käytössä Suomessa, kunnes toisen sukupolven eurokoodit otetaan käyttöön. Lisätietoja eurokoodeista www.eurocodes.fi.