Equipment for crop protection. Knapsack combustion engine-driven airblast sprayers. Safety and environmental requirements and test methods (ISO 28139:2019)
Tuote ladattavissa hetiToimitusaika on noin 1 - 2 työpäivääToimitusaika on 3 - 5 työpäivää.
This document specifies safety requirements and their verification, environmental requirements and related test methods, and minimum performance limits, for the design and construction of knapsack combustion engine-driven airblast sprayers as defined in 3.9. It describes methods for the elimination or reduction of hazards arising from their use. In addition, it specifies the type of information on safe working practices to be provided by the manufacturer. It addresses general operating parameters as well as the potential deposition of spray droplets under specified controlled conditions. This document deals with all significant hazards, hazardous situations and events, excepting those arising from vibration transmitted to the back of the operator. It is applicable to knapsack combustion engine-driven airblast sprayers when they are used as intended and under the conditions foreseeable by the manufacturer (see Table A.1). It is not applicable to: — hydraulic pressure sprayers; — thermal sprayers; — cold foggers; — sprayers adapted for the application of dry material. It is not applicable to knapsack combustion engine-driven airblast sprayers manufactured before the date of its publication. The requirements of this document applies to products manufactured 18 months after publication.
Tämän julkaisun valmistelusta Suomessa vastaa Metalliteollisuuden Standardisointiyhdistys ry, puh. 09 19 231 (vaihde).
Sisällysluettelo
Foreword
Introduction
1 Scope
2 Normative references
3 Terms and definitions
4 Safety requirements and/or protective measures
4.1 General
4.2 Stability when in operation
4.3 Exhaust system
4.4 Air tube and chemical hoses
4.5 Controls
4.6 Machine support
4.7 Power-driven components
4.8 Fuel tank
4.9 Protection against contact with hot parts
4.10 Electrical requirements
4.11 Vibration
4.12 Noise
4.13 Electromagnetic immunity
5 Environmental requirements
5.1 General
5.2 Absorbency of carrying straps
5.3 Spray tank
5.4 Strainers and filters
5.5 Droplet size
5.6 Air hoses and chemical hoses
5.7 Fan
5.8 Mass of total residual liquid
5.9 Stability
5.10 Spray liquid flow rate
5.11 Test report
6 Tests
6.1 Test liquids and equipment
6.2 Test conditions
6.3 Spray liquid output
6.4 Mass of total residual liquid
6.5 Stability
6.6 Contents gauge scale and total tank volume
6.7 Filling rate
6.8 Air velocity
7 Information for use
7.1 Instruction handbook
7.2 Marking
7.3 Warnings
Annex A List of significant hazards (informative)
Annex B Sampling grid position for air velocity determination (normative)
Annex C Stability test (normative)
Annex D Example of a knapsack combustion engine-driven airblast sprayer (informative)
Annex E Safety signs (informative)
Annex F Position of sprayer and Petri dishes for potential ground deposit determination (informative)
Annex G Sprayer locking device (informative)
Annex H Device for detecting potential vertical deposits (informative)
Annex I Potential ground deposit, potential vertical deposit and droplet size test (informative)
Annex J Minimum content of test report (informative)
IEC 61032:1997 Protection of persons and equipment by enclosures - Probes for verification
ISO 11684:1995 Tractors, machinery for agriculture and forestry, powered lawn and garden equipment — Safety signs and hazard pictorials — General principles
ISO 12100:2010 Safety of machinery — General principles for design — Risk assessment and risk reduction
IEC 61032:1997 Protection of persons and equipment by enclosures - Probes for verification
ISO 11684:1995 Tractors, machinery for agriculture and forestry, powered lawn and garden equipment — Safety signs and hazard pictorials — General principles
ISO 12100:2010 Safety of machinery — General principles for design — Risk assessment and risk reduction
ISO 13857:2019 Safety of machinery — Safety distances to prevent hazard zones being reached by upper and lower limbs
ISO 14982:1998 Agricultural and forestry machinery — Electromagnetic compatibility — Test methods and acceptance criteria
ISO 19732:2007 Equipment for crop protection — Sprayer filters — Colour coding for identification
ISO 19932-1:2013 Equipment for crop protection — Knapsack sprayers — Part 1: Safety and environmental requirements
ISO 19932-2:2013 Equipment for crop protection — Knapsack sprayers — Part 2: Test methods
ISO 22867:2011 Forestry and gardening machinery — Vibration test code for portable hand-held machines with internal combustion engine — Vibration at the handles
ISO 22868:2011 Forestry and gardening machinery — Noise test code for portable hand-held machines with internal combustion engine — Engineering method (Grade 2 accuracy)
ISO 3767-5:2016 Tractors, machinery for agriculture and forestry, powered lawn and garden equipment — Symbols for operator controls and other displays — Part 5: Symbols for manual portable forestry machines
ISO 3864-1:2011 Graphical symbols — Safety colours and safety signs — Part 1: Design principles for safety signs and safety markings
ISO 5681:2020 Equipment for crop protection — Vocabulary
ISO 9357:1990 Equipment for crop protection — Agricultural sprayers — Tank nominal volume and filling hole diameter